Nacra F17 Sloop

INTERNATIONAL NACRA CLASS ASSOCIATION HANDBOOK
PUBLISHED

FORWARD

This handbook includes the Class Rules for NACRA F17 Sloop Catamarans (F17SL). These Class Rules are effective as of June 26, 2008 and have been authorized by
INTERNATIONAL NACRA CLASS ASSOCIATION.

The NACRA F17SL Class is intended to be a strict one-design class. A certain degree of latitude in the Class Rules permits skippers to rig their boats to their personal liking for convenience in sailing. However, the Class Rules do not permit any alterations that will
make a standard factory boat less competitive than other boats.
NACRA F17SL sailors shall adhere to these Class Rules when racing as a one-design
class and/or Portsmouth open class. Unlimited events such as long distance
races and demonstration events may make exceptions to these Class Rules
provided that sailors are notified in the Notice of Race. The one-design
Class Rules shall be followed at all regional, national, and world
championship regattas within North America. International Formula Classes
may differ from INCA Rules.

Any questions regarding these Class Rules must be submitted in writing.
Please send questions to the International Nacra Class Association, at
1800 E. Borchard Avenue, Santa Ana, California 92705, USA.

NACRA F17SL Class Rules pertaining to One Design Control as amended for North
America.

1. OBJECT OF CLASS RULES

1. 1 The NACRA F17SL Class Catamarans are a one-design
manufacturers class. The rules, official plans and specifications are
intended to ensure that the catamarans of this class is, as nearly as
possible, the same in regards to shape, weight of hulls, daggerboards,
rudders, spars, sails, and that the equipment is simple, functional and
dependable. The ultimate intent is to encourage the use of only racing
tactics and sailing skill to increase boat speed.

2. PROTECTION OF NACRA F17Sl CLASS DESIGNS

2. 1 The hulls, daggerboards, rudders, stocks, standing rigging, spars
and sails are strictly controlled except as specified in these rules.
Interpretations of these rules shall be given by Performance Sports International,
Inc. (P.S.I., Inc.) in consultation with proper committees of the International Nacra Class Association (hereinafter referred to as INCA). In
the event of a conflict between rules, official plans, measurement form and
/or measurement diagram, the matter shall be referred to INCA. (NOTE: To
doubly guard against "loophole destruction" of these fine NACRA F17SL
Class Catamarans and their potential for lasting racing pleasure, every
deviation from past practice or precedent which is not specifically spelled
out by plans, specifications or Design Rule is assumed illegal until
approved and thus recorded in writing by those administering the Class
Designing Rules.)

2. 2 MOLDS. All molds, patterns and templates for the hulls,
daggerboards, and rudders shall be constructed solely by P.S.I., Inc. or
the builders licensed for that purpose by P.S.I., Inc., for NACRA
construction.

2. 3 ALTERATIONS TO MOLDS. No alterations shall be made to any molds,
official patterns or templates.

2. 4 CONTROL OF MOLDS. All molds shall be pulled from the official
class plugs maintained by P.S.I., Inc., and shall not be modified in
shape except to fair any surface imperfections.

3. HULLS, DAGGERBOARDS AND RUDDERS

3. 1 THE MANUFACTURE of hulls, daggerboards and rudders is strictly
controlled by P.S.I., Inc. Licenses to build these components are issued by P.S.I., Inc., for NACRA.

3. 2 ALTERATIONS TO HULL, DAGGERBOARDS AND RUDDERS. Grinding, planning, sanding and/or application of putty, fillers and coatings on the outside
surface are permitted provided that it is undertaken to fair local
imperfections in these surfaces or to improve the surface finish and not to
alter the intended shape of any surface.

3. 3 HULL WEIGHT. The hull weight may not be reduced by removing any
material except for the installation of inspection ports. A maximum of
three inspection ports per hull are allowed. Inspection ports are not
permitted forward of the main beam. None may have an opening larger than
six inches.

3. 4 RUDDERS. The rudder and rudder stock assembly, including the
method of attachment to the transom is not to be modified. Rudders may be
raked to attain helm balance. Rudder shape and length may not be changed.
Nacra F-18 Rudder blades are permitted.

3. 5 DAGGERBOARDS. The top of the daggerboard may not be inserted below
the hand well. The shape and length may not be changed. No part of the
daggerboard or daggerboard well may be removed or added for the purpose of
varying rake. All daggerboards manufactured by NACRA are legal for racing
except ones that require modification of daggerboard or daggerboard well
to accommodate them. F17SL daggerboards may be modified in length and

profile as per template provided by P.S.I., Inc.

4. SPARS
4. 1 CONSTRUCTION. The material, method of construction and design of
the spars shall be in accordance with these rules and official Spar Plan.
The mast, spreader, boom, beam, tiller and tiller tie bars shall be
fabricated only by NACRA or builders licensed by P.S.I., Inc., for NACRA.

4.2 MAST. The extrusion length and position of the masthead, mast
hound, jib halyard strap eye, spreader and mast base are not to be altered
in any manner. The gooseneck and diamond wire tangs may not be moved from
the factory supplied position. Rotator arm maybe relocated using the new casting, control system is open.

4.3 SPREADERS. The spreader arm lengths may not be altered. NACRA F17Sl
adjustable rake spreaders are allowable on all models. The diamond wires
are to be securely attached at the spreader ends.

4.4 BOOM. The boom extrusion shall be supplied by the manufacture. Outhaul and rotation control maybe modified.

4.5 BRIDLE FOILS. Bridle foils are not allowed and are considered not class legal.

4.6 MAIN BEAM. The aluminum extrusion length, mast step and dolphin
striker assembly are not to be altered. Internal controls may be
installed.

4.7 REAR BEAM. The aluminum extrusion length may not be altered with
the following exceptions: internal controls limited to crew restrainer
systems only.

4.8 TILLERS, TILLER TIE BAR AND EXTENSION. Tillers and tiller tie bar
may be shortened. Tiller extensions (hiking sticks) and design are
optional.

4.9 SPAR WEIGHT. No holes may be drilled, filed or cut into any
manufacturer supplied component, spar or casting for the purpose of
reducing weight.

5 RIGGING

5.1 CONSTRUCTION. All standard rigging (including diamond wires) shall
conform with the wire types and, diameters shown in the manufacturers
rigging schedule, wire diameters shall not be less than those shown in the
rigging schedule. Running rigging and associated blocks, shackles, and
cleats are not controlled except as specified in these rules. Rope tails
on halyards are permitted. Jib halyards may not be led internally in the
mast. Halyards must be long enough to raise and lower sails while the boat
is in an upright position. (NOTE: wire length is measured from bearing
point to bearing point.)

Rigging Schedule:
Wire type Minimum Wire – Diameter - Lengths
Shrouds             1 x 19    1/8"
Forestay             1 x 19     1/8"
Diamond Wires 1x19 1/8
Trapeze Wires   1x19 3/32
Bridle               1x19 5/32”, minimum 53.5” in length

5.2 MAIN LUFF tension systems are optional but may not be led
inside the mast.

5.3 TRAPEZE. Double trapeze system only is allowed on NACRA F17SL. No continuous trapeze systems are allowed.

5.4 FOOT STRAPS, SAFETY LINES, or the like may be added to assist the
crew to trapeze. Hiking assist inboard is optional.

5.5 ALTERATIONS. Lengths of bridle wires are not to be altered. The forestay or its extension is to be attached at the bridle intersection. The forestay,
shrouds, and diamond wires shall not be adjusted while racing.

5.6. EQUIPMENT may be added or changed to conform with current or
previously supplied NACRA series production equipment. All such equipment
supplied for NACRA F17SL shall be considered class legal.

5.6a Main sheet purchase may not exceed 8:1 on any boat. Multiplier or
fine tuning systems (Magic Blocks) are illegal.

5.6b Trampolines; all boats must be equipped with an NACRA licensed
trampoline. Hiking straps, spinnaker and equipment bags may be added or
altered. Up to 8 grommets or straps may be added as gear attachment points. No other modifications are allowed. The tramp size, shape, and method of attachment to the hulls or beams may not be altered.

5.6c Downhaul may not exceed 8:1.

6.1 CONSTRUCTION. The material, method of construction and design of
the sails shall be in accordance with the sail plan. The sails for the
NACRA F17SL shall be built for NACRA from patterns and sail cloth
approved by NACRA. Sails shall be fabricated by builders licensed by P.S.I., Inc., for NACRA. Battens may be of wood, carbon, foam fiberglass or
fiberglass. A set may consist of a combination of these types. All batten
pockets must contain battens while racing, the only exception being a torn
sail which loses a batten or battens during a race from a damaged batten
pocket. (Only one batten per pocket is permitted.)

6.2 ALTERATIONS. The mainsail can not be re-cut. The spinnaker may not be re-cut. Windows, tell-tale windows, and chart pockets are optional. Class insignias may not be repositioned or altered in any manner. A minor repair to the sail may be done by a local sail maker as long as there is no alteration to the original shape or sail design. Any sail extremely damaged (panel replacement) and/or requiring seam repair must be repaired and re-measured by a INCA licensed sail maker

6.2a Sail reinforcement. Load straps may be applied to the following corners, head, clew, tack and cunningham on the main, jib and spinnaker. Straps may not exceed 12 inches from bearing surface. Chafing strips may be added to mainsail batten pockets where they come in contact with the shrouds. Spreader patches are
allowed.

6.4 Number of sails allowed in an event; one mainsail, jib and one spinnaker. Changes allowed in an event do to damage, either major repairs or replacement can only be done with jury approval.

6.5b. Aluminum Mast: The current large head vertical cut mainsail, the small head vertical cut mainsail, and the cross cut large head mainsail are legal.

6.6a. F17SL sails will be sequentially numbered as they are produced for Nacra by a licensed Nacra sail maker. All sail numbers will be numerical in nature, no alphabet letters. Example, 123, 717, etc. Only ISAF designated country code letters will be used in conjunction with numbers. Example, USA 123,

USA

717, etc.

6.7a The Nacra F17 large spinnaker will be the class legal spinnaker, But may use the F17 standard spinnaker.

7. CREW: Class legal minimums

7.1 Minimum Live Sailing Weight, Minimum Sailing Weight, corrector weight location and method of fixation;

7.1a Minimum Sailing Weight shall be the weight of the crew at registration, dressed in shorts / t-shirt or swim suit, and barefoot. Normal undergarments may also be worn with the aforementioned clothing.

7.1b Minimum Sailing Weight shall be the Minimum Live Weight plus corrector weights if necessary.

- The NACRA F17SL Minimum Sailing Weight shall be 245 lbs, however, for crews weighing less than minimum sailing weight, ½ of the additional weight required must be carried. (See WEIGHT CHART NACRA F17SL below)

7.1c Corrector Weights; corrector weights shall be attached to the trampoline within 18” from the front main beam or placed into the stock storage pouch. Weights shall be securely attached to the boat and shall not be moved while racing. Attachment shall be with tape, zip ties, or by tying with line led thru the weights. Screws, rivets, nuts and bolts are not allowed. Weights must be easily accessible and easy to remove for check weighing.

.
7.2 Boat Weight. The NACRA F17SL shall have no minimum class
weight, but there are no alterations allowed to standard construction for
the purpose of reducing weight from the manufacturer-supplied condition.

8.0 SAFETY EQUIPMENT. All NACRA F17SL catamarans are responsible to carry safety equipment as required by the U. S. Coast Guard while racing.

8.1 One PFD must be worn by each crewmember while racing.

8.2 A righting line of 3/8" minimum diameter and 14' minimum length.

9.0 SPINNAKERS, POLES, AND RIGGING

9.1 Spinnaker is considered class legal for NACRA F17Sl sanction regattas,
spinnaker shall be fabricated by builders licensed by P.S.I., Inc. for
NACRA F17SL.

9.2a E-O Snuffer or mid pole systems are considered class legal if purchased through P.S.I., Inc. The spinnaker tack distance from the front beam must remain the same.

9.3 Rigging spinnaker attachment points bale, hound, etc. shall not be
modified from stock configuration. All lines and blocks are left to the
boat owner.

10. WARRANTY. Modifications allowed by these class rules may not
necessarily be covered by the manufacturer's warranty. Modifications
outside of the class rules, such as larger spinnaker, will void the
manufacturer's warranty.

11. COMMUNICATIONS, RULE INTERPRETATION AND AMENDMENTS

11.1 Valid questions regarding these rules must be mailed to INCA
headquarters.

11.2 Class rules may vary slightly from one country to another. Do not
assume that the rules that apply for the United States will apply in
another country. Be certain to familiarize yourself with the class rules
of the country in which you are competing. A licensed NACRA F17SL builder in
another country may modify the INCA class rules for that country provided
that they have been approved by INCA.

11.2a The manufacturer, P.S.I., Inc., reserves the right to make changes to
the class rules, if the class membership falls below fifty active class
members.

11.2b Class voting is to be held only by active class members, which are
class members prior to the issue being voted on. An active class member is
a NACRA F17SL class boat owner, whose annual class dues have been paid.

11.2c Annual Class Dues cover membership from January 1st through
December 31st of the year paid.

11.3 For International Events, the class rules will be approved by INCA
and P.C., Inc., the manufacturer, and listed in the racing instructions.

11.4 INCA consists of a governing board of directors, fleet directors,
and an official rules and policies committee. Class rules are governed by
the manufacturer.

11.4a Rule changes. A proposal must be presented to the Class Board to amend an
existing class rule or a change in the boat design. Send a detailed letter
to Rules and policies committee. Ballot wording and content is the
responsibility of the Rules and Policies Committee.

11.5 The NACRA F17SL may not conform to International Formula
Rules.

11.6 The Nacra F17SL may race as a Class legal F17 with the removal of the jib & proper spinnaker.

The INCA mailing address is:

International Nacra Class Association
1800 East Borchard Avenue
Santa Ana, CA 92705

U.S.A.

CREW WEIGHT IN LBS.	SPINNAKER	ADDED WEIGHT
230	large	7.5 lbs
235	large	5 lbs.
240	large	2.5 lbs.
245	large	0

SAILORS ARE RESPONSABLE FOR TAKING THEIR OWN ADDED WEIGHT, WHICH MAY BE CHECKED AND PROTESTED AT ANY TIME DURING A RACE.